![]() STEP 4 When the login page appears, enter the default user name cisco and the default password cisco (lowercase). Check the Port Activity to see if a WAN connection is enabled. STEP 6 To use the setup wizard to configure your Internet connection, click Setup Wizard on the System Summary page. Or click Wizard in the navigation tree and in the Basic Setup section, click Launch Now. If you have trouble connecting to the Internet or the web-based web interface: STEP 7 To configure other settings, use the links in the navigation tree. Verify that your web browser is not set to Work Offline.Check the local area network connection settings for your Ethernet adapter.The PC should obtain an IP address through DHCP. Verify that you entered the correct settings in the Wizard to set up your Internet connection.Īlternatively, the PC can have a static IP address in the 192.168.1.x range with the default gateway set to 192.168.1.1 (the default IP address of the device).Reset the modem and the device by powering off both devices.Next, power on the modem and let it sit idle for about 2 minutes. If you have a DSL modem, ask your ISP to put the DSL modem into bridge mode.The user interface is designed to make it easy for you to set up and manage your device. The major modules of the web interface are represented by buttons in the left navigation pane. Some links and buttons launch pop-up windows that display more information or related configuration pages. If your web browser displays a warning message about the pop-up window, allow the blocked content. The System Summary displays information about the current status of the device connections, status, settings, and logs. Serial Number-Serial number of the device.Firmware version-Version number of the installed firmware.PID VID-Version number of the hardware.MD5 Checksum-A value used for file validation.LAN IPv4/ Subnet Mask-IPv4 management IP address and subnet mask of the device.LAN IPv6/ Prefix-IPv6 management IP address and prefix.Working Mode-Controls the behavior of the device in relation to the WAN connection.Gateway Mode is selected when the device is hosting an Internet WAN connection. Router Mode is selected when the device is on a network that does not have a WAN connection or another device is used to establish the WAN connection. To change this parameter, click Working Mode to display the Advanced Routing window. If Dual-Stack IP is enabled on the Setup Network page, the IPv6 address and prefix length also appear. System Up time-Length of time in days, hours, and minutes that the device has been active.Port Activity identifies the port interfaces and indicates the status of each port: To access the Internet connection setup wizard and be prompted through the process, click Setup Wizard to launch the Wizard. Interface-Type of interface: LAN, WAN, or DMZ.Multiple WAN interfaces are indicated by a number, such as WAN1 or WAN2. Status-Status of the port: Disabled (red), Enabled (black), or Connected (green).Click it to open the Port Information window. The Port Information window displays detailed information about the interface and the current activity on the port: To display detailed information about current link activity, click the Status entry for the port. Type-Type of port: 10BASE-T or 100BASE-TX or 1000BASE-T.Interface-Type of interface: LAN, DMZ, or WAN.Link Status-Status of the link: Up or Down.Port Activity-Current activity on the port: Port Enabled, Port Disabled, or Port Connected.Priority-Port data priority: High or Normal. ![]() Speed Status-Port speed: 10 Mbps to 1000 Mbps.Duplex Status-Duplex mode: Half or Full.Auto negotiation-Status of the auto negotiation parameter that when enabled (On), detects the duplex mode, and if the connection requires a crossover, automatically chooses the MDI or MDIX configuration that matches the other end of the link.In System Summary, it displays a number of 30 possible connections, however, only two clients can connect.There are two predefined VLANs: 25 and 100. I set up my RV320 to use client to gateway connection with Easy VPN authenticating through AD, I get two connections, however, after connecting no more clients.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |